Telescopic metallic mezzanine. It is ideal to double the space of your living room, offices, rooms, studios, playrooms, garages, lofts,…. Whatever your space is, we have a solution for you.
Warning: Last items in stock!
Tecrostar mezzanines and stairs are supplied with everything you need to install the kit at its maximum surface area or height.
Personalised phone or email service from our specialists
The kit includes as many boards as needed to install the mezzanine in its maximum dimensions. To install the mezzanine in smaller dimensions, it is necessary to cut the boards as it is explained in the installation manual included in the mezzanine kit. Cutting the boards is really easy and all the required tools are available at our online store as well.
No. Tecrostar does not have a different flooring alternative. However, it is possible to personalize the finish of the floor by adding some accessories on the boards (carpet, platform,...). Check our floor finishes in accessories section. If the customer installs a different floor from the boards provided, it is their responsibility to ensure the resistance of the full mezzanine, since the floor contributes to the stability of the whole.
No, you can’t. At the moment, our mezzanines are available just for a single height although some customers install them on another existing mezzanine. In that case, the resistance of the existing one should be checked.
It depends on the beam type, we need to calculate the corresponding surface load. For example, a secondary beam TM15 supports around 560 kg. You should take into account that if we apply additional loads, a part of the bearing capacity of the beam is being consumed.
If you have any doubt about important additional loads, contact our technical department.
TecroStar products can be installed outdoors (in the open), provided that the following considerations are taken into account, which define the structural, environmental and material maintenance calculation conditions.
material maintenance calculation conditions.
1.- Outdoor installation involves forces due to snow and wind, which depend on the geographical location, altitude of the site, etc. These actions have been taken into account in the calculation, with certain maximum values that must be compared with those of the area where it is installed, to ensure that these limits are not exceeded.
2.- The snow-bearing capacity value must be subtracted from the total usage load bearing capacity, taking into account the dimensions of the mezzanine. As a guide value, TecroStar structures can be considered to withstand a minimum use overload of 200 kg/m², and therefore the load of snow that a mezzanine can withstand outdoors is very high.
3.- The mezzanine can be installed as an outdoor canopy by installing the stability kit, contemplating the case of a complete obstruction when it is placed against a façade, or free if it allows air to pass through its lower part. A wind speed of 100 km/h is taken as a reference. The regulations of each locality must be consulted to check that these limits are not exceeded.
4.- Under no circumstances should the sides of the building be closed, as this implies greater horizontal forces that are not included in the calculation.
5.- The columns of the mezzanine must be fixed to a solid base that resists the actions transmitted by the mezzanine.The TecroStar team provides guidance on the type of footing or foundations required under the columns. If you wish to place the mezzanine on a surface like grass or soil, some type of footing will also be required. The modular foundations system shown at https://piloedre.es/ could be a good solution. In both cases, it is the client's responsibility to check the final resistance of the ground with the technician in charge of the project.
The specifications shown below refer to the characteristics of TecroStar products WITHOUT WATERPROOFING, as this treatment offers greater protection to the steel parts against rusting (for more information go to tecrostar.com/en/faqs/mezzanines/waterproof-treatment-of-steel.html).
TecroStar structures have a thermosetting polyester polymerised powder coating, with a coating thickness between 60 and 80 microns. Corrosivity category C2 has been obtained, of medium durability, when submitting the pieces to the tests, according to the criteria of the European Norm EN ISO 12944 of May 1998: "Protection of steel structures against corrosion by means of protective painting systems". This rating is valid without waterproofing treatment. Examples of typical environments for corrosivity category C2:
• Indoors: buildings without heating where can form condensation (warehouses, sports centres…)
• Outdoors: atmospheres with low pollution levels. Mostly, non-coastal rural areas.
The medium durability of the lacquer covers a period of 5 to 15 years. The standard states that durability is NOT a "warranty period". Durability is a technical consideration that can help the owner establish a maintenance programme. This means, tests are performed for a specified number of hours under uniform conditions applied to smooth surfaces. The reality is that climatic and environmental conditions are very variable.
The edges of steel parts are the parts most prone to corrosion and where rust first appears, in fact, these areas are not evaluated in salt spray tests, as the standard does not contemplate them.
The metallic steel pieces are lacquered with paints suitable for exteriors, but it is expected that, after a while, the structure requires paint retouching on localised areas, like edges or corners, that may show signs of oxidation and loss of gloss. It is recommended to polish these areas to remove the rust and then apply the paint.
TecroStar does not advise the use of metallic parts painted in white for exteriors, since the appearance of rust is appreciated much earlier than in black components.
If the mezzanine is to be installed outdoors in a marine or coastal environment, maintenance recommendations should be carried out more frequently, due to the corrosive power produced by the existence of salt and moisture. Ensure the control of the oxidation process to avoid further deterioration. In this case, it is recommended to polish the affected areas to remove the rust and then apply the paint.
The aluminium handrails of the rails do not require any special maintenance, as all of them are subjected to surface treatments that guarantee their outdoor performance (anodised silver, black lacquer or with a wood effect).
The load-bearing floor of TecroStar mezzanines consists of structural plywood panels. It is intended for indoor use in a humid or protected outdoor environment in accordance with EN 636-1-S. The customer must apply a lasur* or specific waterproofing treatment for wood to the floor and to the exposed edges, which protects the surface and prevents water from penetrating into the tongue and groove joints of the panels and affecting the edges.
Another aspect to bear in mind for the optimal maintenance of the structure is to seal the grooves with silicone and cover the top opening in order to prevent moisture from penetrating the structure. For preservation purposes, it is essential to insert plugs in the holes of the columns.
Likewise, all wood pieces (steps, wooden strips, etc.) must be treated with some type of water-resistant paint or varnish to prevent moisture from penetrating and the material from cracking, and therefore losing its mechanical and aesthetic characteristics. In addition, it is important to check that any coatings applied (varnish or paint) have not deteriorated, touching them up if necessary.
The presence of water in puddles or “ponds” on the mezzanine should be avoided. To that end, the mezzanine should be installed with a slight slope (approximately 2%) to facilitate the water evacuation and to avoid its accumulation. This unevenness can be achieved by installing levelling plates under the highest pillars of the structure. Drains can also be created for the same purpose.
* It is a product for outdoor uses that is more appropriate than varnish because it offers a high resistance, does not create a layer on the surface it is applied, controls humidity, gives a waxy finish and provides a wide range of finishes.
No, our mezzanines are sold with columns by default. We cannot guarantee the resistance of walls or corbels and the customer will be responsible if the product is modified in these cases.
Yes. Provided that the inclination is small, we can use a wedge under the mezzanine columns to level it. If the inclination is too small it might be not necessary at all and the slope might be imperceptible.
You can adjust the structural floor, working around architectural barriers or irregular surfaces.
When the walls are irregular or when you want to work around a fixed object, the decking can be finished off against the wall
Adjustment from below:
Adjustment from above:
It is possible at lower height but it requires to cut the columns and drill again though. At higher height is not possible. The cut of the columns can be done by the customer or you can order Tecrostar to do it upon request for a quote.
Yes. This is quite common and the results are very good. The telescopic system of the columns enables the height to be adjusted every 6 cm.
You can make aesthetic modifications, but any structural modification non approved by Tecrostar will be under customer’s responsibility.
Yes, you can. However, the maximum load capacity will be unaffected.
To install Tecrostar mezzanines you need 2 adults (they do not need to be DIY experts). It is recommendable to use personal safety equipment like gloves, boots, etc. in order to avoid accidents.
When installing range L mezzanines you may need to use some type of scaffolding or ladder for working at heights and manual or electric lifting machinery to raise the primary beams, particularly if the structure is more than 3m high. The other ranges can be lifted easily by hand.
You will need the following tools to install the mezzanines: tape measure, some type of spanner for m10 and m8 bolts and a screwdriver (an electric screwdriver will make the task much easier), spirit level, drill and a tool for cutting the panels (saw, jigsaw, circular saw, etc.)
You can find all the tools required to assemble it and tested by Tecrostar in the tools section.
All the models are installed by following these steps:
Pre-assemble the structure on the floor in the desired area.
Raise the outer structure to the desired height.
Finish assembling the structure and floor.
You can do it yourself with the help of a friend. It is easily installed in a few hours, depending on the product.
TS8 Mezzanine: 3 hours with 2 people
TM15 Mezzanine: 4 hours with 2 people
TL30 Mezzanine: 5 hours with 3 people
The times are a guideline and for assembly only. You need to add the time it takes to measure up, move the components to the location, clean up, etc.
You can find an installer nearby on the web misterassembler.com.
This website is foreign to Tecrostar. It puts installers and customers in contact, so the price and the responsibility for the installation are the installer, not Tecrostar.
Mezzanines are shipped in boxes by an external company in a lorry with a tail lift that enables the box to be unloaded to the ground (at street level at the customer’s address).
Depending on your order you can receive different packages: One box for the mezzanines of the S and M ranges or two boxes for L mezzanines.
Length: 239 cm
Width: 112 cm
Height: 54 cm
The stairs can share the box with the mezzanines if they are purchased at the same time or you can have a separate box for the stairs. Check the stairs section.
Don't be alarmed by the total weight of the product, the components are light and manageable, so you can move them easily and take them up in the lift. The heaviest components are the primary beams from the L range (39 kg), the rest of the ranges are considerably lighter (12kg). The floor panels are very light and fit in any lift. No component is more than 2.4m long and therefore, fits in most lifts.
In most cases, you can.
Our product is totally detachable and reusable. Therefore, it can be considered as movable property. This feature, always depending on each country’s current legislation, allows its use and installation inside any dwelling, garage, plot or industrial unit with no need for planning permission.
For instance, under the Spanish regulations, detachable mezzanines are considered as movable property, and they do not require planning permission in order to be installed.
Following this logic and due to the characteristics above mentioned, TecroStar mezzanines should not be catalogued as part of the built-up area. Hence, our platforms should be under the same legal regime as machinery, shelves, racks, vehicles, etc.
Regardless of this consideration, on each one of the projects the Client must check in advance whether the load capacity of the building where the mezzanine is to be installed is sufficient, as well as the most up-to-date current legislation.
Sometimes, the carrier cannot access to point of delivery due to an extremely narrow street or any other difficulty. In such cases, the carrier cannot do the delivery with the usual truck and he may need to use a different vehicle or extra support. If the carrier considers that the point of delivery is complicated, request a quotation. If you don’t inform in advance that the access is complicated, the delivery will be paralysed until you pay the extra cost.
Tecrostar products are manufactured with the most suitable materials for the proposed technical solutions, combining wood, steel and top quality aluminium.
TECRO has earned certification from the AEM, the federation of Spanish materials handling. We have also received a Gold Medal Award of Merit from the INPEX (Invention and New Product Exposition), the top award for innovation at the largest Invention Exposition in the USA.
Our delivery times are based on historical statistical data related to Tecrostar experience in the last decade. In spite of the difficulty of providing an exact information, you can check here the approximate data in real time.
Our preparation times of the material can be sometimes affected by:
The shortage and speculation around the raw materials.
The logistic difficulty that implies a product with great volume and its different configurations.
The bank holidays that paralyze our activity.
Personal errors that force us to restart or improve certain processes.
We are human!
No related articles on blog
The Tecrostar mezzanine allows an easy installation in any surface without works. Its design, unique in market, makes it extensible lengthwise and width wise and turns it into the most versatile mezzanine both for homes and offices or warehouses. The TM15 Mezzanine supports any furnishings: it resists loads from 200 kg/m². It is a metallic structure totally adjustable. It doubles its area from 5 to 15 m² and its height, length and width can be adjusted maintaining the stability.
It is necessary to use the Beam for interior Stairs M to install any of our staircases inside the structure.
Our product is totally detachable and reusable. Therefore, it can be considered as movable property. This feature, always depending on each country’s current legislation, allows its use and installation with no need for planning permission. Tecro Space, SL is not responsible of the use or inadequate installation of the product.
The products can be located indoors and outdoors taking into account some recommendations.
The material will be delivered at street level (curbside delivery) by an external transport company.
Check our delivery times in real time here.
We do deliver worldwide. Request an offer now.
|Type of product||Only Mezzanine|
|Maximum height above the flooring board (cm) (HT)||282|
|Minimum height above the flooring board (cm) (HT)||173|
|Total height (cm)||173, 179, 185, 191, 197, 203, 209, 215, 221, 227, 233, 239, 245, 252, 258, 264, 270, 276, 282|
|Height-adjustable every (cm)||6,05|
|Total maximum load (Kg)||2200|
|Beam height (cm) (HB)||20|
|Width/Length-adjustable every (cm)||10|
|Maximum length of the primary beam (cm) (LT)||415|
|Minimum length of the primary beam (cm) (LT)||225|
|Maximum length of the secondary beam (cm) (DT)||361|
|Minimum length of the secondary beam (cm) (DT)||201|
|Maximum area (m²)||15|
|Minimum area (m²)||5|
|Load capacity in its minimum extension (kg/m²)||500|
|Load capacity in its maximum extension (kg/m²)||200|
|Flooring||European Radiata pine plywood 18 mm thick|
|Maximum load (Kg)||2000|
|Material and finish of the structure||Structural steel painted with powder coating|
|Net weight (Kg)||378|
|Gross weight (Kg with packaging)||410|
thank you for your interest in our products.
This mezzanine can be adjusted in intervals of 10 cms (width and lenght) and 12 cms (height); therefore you can set it at, either, 209 or 221 cms high.
Gabriele Iacobucci - Customer Service.
Montage relativement facile , bonne rigidité
Montage assez facile quand on bricole , l'idéal est de s'équiper d'une clé à choc car beaucoup de boulons et écrous pour la TM15 !
Une fois terminée la rigidité est bien là ...
La seule chose à amélioré reste les vues du plan de montage surtout au niveau des équerres d'angle !Le plan fourni n'est pas toujours top
L'équipe TECRO est tres sympa , toujours dispo par téléphone dans un Français impeccable .
L'emballage de livraison est vraiment soigné et robuste .
Cette entreprise est très sérieuse .
Mezzanine de qualité
Je recommande cette mezzanine, je suis très satisfait de mon achat qui m'a fait augmenter mon logement d'une grande chambre supplémentaire, produit de bonne qualité, instruction de montage clair, mezzanine stable..
Le service client très réactif et répond à tout vos questions.
Super kit facile à installer, solide, et qui rend bien!
J'ai acheté ce produit sur internet pour faire un essai, créer une mezzanine dans mon garage pour stocker mes affaires.
Surprise, j'ai à faire à des professionnels, des gens sérieux, qui livrent dans les délais promis, et qui fournissent du matériel superbe tel que décrit sur leur site.
Rien à dire, ça se monte comme un grand meccano, le matériel est solide et agréable à regarder, le résultat est superbe et fonctionnel